GBBR M-4 and such
3 posters
Page 1 of 1
GBBR M-4 and such
Hey Allout,
What was the Website for the GBBR ? I am going to order the NPAS and that high tech trigger Mech.
Okay I found it! Man that high tech trigger mech is expensive Allout
What was the Website for the GBBR ? I am going to order the NPAS and that high tech trigger Mech.
Okay I found it! Man that high tech trigger mech is expensive Allout
Howie- Your the Man
- Posts : 1785
Join date : 2010-03-07
Age : 48
Location : Milton Florida
Re: GBBR M-4 and such
Hey GBBR user's check this out, Nice website to assist us,
[You must be registered and logged in to see this link.]
[You must be registered and logged in to see this link.]
Howie- Your the Man
- Posts : 1785
Join date : 2010-03-07
Age : 48
Location : Milton Florida
Re: GBBR M-4 and such
great stuff, good info , here's some more [You must be registered and logged in to see this link.]
allout- Admin
- Posts : 956
Join date : 2010-03-24
Re: GBBR M-4 and such
Hey Allout,
I got the M-4 with .20 @ 395-398, > .25 @ 370-375 > .30 @ 340-350 I adjusted the NPAS valve along with drilling 7/64 hole in side port. I'll post some pic up for you and other fellow GBBR.
That 7/64 hole was an bad idea, need to order another brass nozzle
I got the M-4 with .20 @ 395-398, > .25 @ 370-375 > .30 @ 340-350 I adjusted the NPAS valve along with drilling 7/64 hole in side port. I'll post some pic up for you and other fellow GBBR.
That 7/64 hole was an bad idea, need to order another brass nozzle
Howie- Your the Man
- Posts : 1785
Join date : 2010-03-07
Age : 48
Location : Milton Florida
Re: GBBR M-4 and such
how was it to install that NPAS ? i ordered one for my WE m4 4168 but im not sure how to install it...
DirtyMo- Novice
- Posts : 43
Join date : 2010-08-30
Age : 35
Location : Fort Walton Beach, Fl
Re: GBBR M-4 and such
it's pretty simple, Open your upper from lower reciever, then re move charging handle, now once the charging handle and internal barrel is out, Unscrew the valve from the guide rod, Do loose the spacer, take it off also, then take flat head screwdriver, to rear and remove bolt, follow by removing the rod, now putting in the NPAS valve is just the same, Use Silicone spray or lube for all orings you see, should be three total. Now adjustments Shot one or two shoots and check against an chrono, Open upper receiver and take special tool and small screwdriver, the speical tools goes down the center and use screwdriver to hold valve in place. Clockwise raises and counterclockwise lowers
Howie- Your the Man
- Posts : 1785
Join date : 2010-03-07
Age : 48
Location : Milton Florida
Re: GBBR M-4 and such
so your talkin about the screw on the back of the bolt hold the everything in place? sorry for the late reply
DirtyMo- Novice
- Posts : 43
Join date : 2010-08-30
Age : 35
Location : Fort Walton Beach, Fl
Re: GBBR M-4 and such
That screw only keeps the pin from seperating. I will post pictures next week.
Howie- Your the Man
- Posts : 1785
Join date : 2010-03-07
Age : 48
Location : Milton Florida
Re: GBBR M-4 and such
aight thanks!!
DirtyMo- Novice
- Posts : 43
Join date : 2010-08-30
Age : 35
Location : Fort Walton Beach, Fl
Re: GBBR M-4 and such
The Upper recievers should be here atleast by next monday before the 11th game, I am wanting to run my GBBR again
Howie- Your the Man
- Posts : 1785
Join date : 2010-03-07
Age : 48
Location : Milton Florida
Re: GBBR M-4 and such
been working on my mags got 8 working good 8 more to go
allout- Admin
- Posts : 956
Join date : 2010-03-24
Page 1 of 1
Permissions in this forum:
You cannot reply to topics in this forum